COLD ROOM DOORS

Our doors;

Our cold room doors have a surface protection system against scratches during installation and consist of galvanized painted, chrome plated, PVC coated platters.

No heat bridges are formed at any point of the cold room doors and the sheets are not allowed to touch each other and are mounted with the latest technology to ensure maximum isolation. Polyurethane is injected without using. There are no side products other than polyurethane material in the doors, but polyurethane is injected without additional panel in case of different sizes for doors. The doors are all 100% Polyurethane filled and have a density of 40-45 kg / m3 at all points.

It provides complete contact with the surface with flexible door tires which are mounted on the cold room doors. The door hinges have a eccentric hinge system (upshifting when opening, downshifting when closing). This type of lock has a built-in lock system that does not protrude from the front door surfaces obtained by special designs.

General Properties of Cold Room Sliding Doors

  • The case junction can be done on panel or the wall.
  • Different threshold heights are used according to usage.
  • Suitable for food regulation, sealing is provided by gasket which does not produce bacteria.
  • The tire is produced as a skirting or threshold according to usage.
  • Frozen storage and fast frozing chambers are produced with resistors. The heating resistor used in resistive doors is 220 Volt supplied and imported. The EPDM material on the door wing allows the resistance cable to be replaced later on in the special capped profile at the point where the durable and flexible seal is pressed against the edge of casement.
  • Rail components are made of aluminum, not rust.
  • The rail components are rising type.
  • The emergency exit allows the door handler to be opened from the inside where the door is locked from the outside.

    • General Properties of Cold Room Hinged Impact Doors

    • The case junction can be done on panel or the wall
    • Different threshold heights are used according to usage.
    • Suitable for food regulation, sealing is provided by gasket which does not produce bacteria.
    • The tire is produced as a skirting or threshold according to usage.
    • Frozen storage and fast frozing chambers are produced with resistors. The heating resistor used in resistive doors is 220 Volt supplied and imported. The EPDM material on the door wing allows the resistance cable to be replaced later on in the special capped profile at the point where the durable and flexible seal is pressed against the edge of casement.
    • All lock and hinge parts are imported.
    • The hinges are the rising type.
    • The emergency exit allows the door handler to be opened from the inside where the door is locked from the outside.

    General Properties of Cold Room Atmosphere Control Sliding Doors

    • Door thickness is 92mm in normal cold storage, 120mm in frozen storage
    • Suspension Hardware Carrier rails, wheels, grips and necessary accessories are composite material and stainless steel.
    • Both sides of the surface sheet standard manufacturing wing are PVC plate. It can be polyester painted sheet and CrNi depending on demand.
    • Door Case: Exterior case is special PVC, internal case is aluminum.
    • The heat bridge is a single row special rubber seal surrounding the door wing in the normal storage rooms. The frozen storage room door has very easily changing resistance when needed.
    • The door material is made from specially reinforced composite material. Special sealing ring is used. Suitable for rooms up to -5 ° C. These doors have a 100% leakage-proof sight window to control the atmosphere inside the room.

    General Properties of Cold Room Single Door Service Bar Doors

    They are doors that can be mounted on panels and walls and are used for transmission passages in both sides with one 180 degree wing and can be opened permanently if necessary, 40mm wing thickness, polyurethane filled, with or without windows, service passages.

    General Properties of Cold Room Double Door Service Bar Doors

    They are doors that can be mounted on panels and walls and are used for transmission passages in both sides with two 180 degree wings and can be opened permanently if necessary, 40mm wing thickness, polyurethane filled, with or without windows, service passages.

     

     

     

Products

 

© Copyright 2010. Yazkar Soğuk Oda - Soğutma Sistemleri is a foundation of Yazkar A.Ş.

Cold Room Storage, Cold Room Systems, Cold Room Panels, Cold Doors, Cold Room Accessories, Cold Room Locked Panels, Cold Room Equipments, Cold Store Evaporator, Cold Storage Capacitor, Cold Room, Cold Room Roof Panels, Cold Room Storage, Cooling Systems Cold Room Equipment, Cold Room Equipments, Cold Room Equipments, Cold Room Equipments, Cold Storage Equipment, Cold Storage Equipment, Cold Room, Cold Room Roof Panels, Cold Room Storage, Cooling Systems, Cold Room Panels, Cold Room Panels, Cold Room Accessories, Doors, Cold Room Accessories, Cold Room Locked Panels, Cold Room Equipments, Cold Storage Evaporator, Cold Storage Condenser, Cold Room, Cold Room Roof Panels